Indoor

e-xt40

Indoor E-XT40 Cover


ENGINE
-Brushless engine with permanents high efficiency magnets. Complete engine with resolver transducer, electronic and On Board power.
-Engine couple: 20Nm continuing
-Nominal continuing power: about 4.600W 6,5 CV (throughout all the battery duration)
Maximum power 16KW about 21,8CV.
- Power reverse
- The maximum suppliable power of the engine is digitally programmable: in this way the user can determine and limitate the power in order to get a longer batteries life.
 

ELECTRONICS
-Integrated in the engine that includes:
- Digital Brushless Power ServoDrive
Full digital, programmable from the PC Browse for a complete user parameterization.
- Digital BMS controller Battery Pack LifePo4
- Digital Battery Pack LifePo4 Charger (battery charger) with power input from the net.
Medium recharge time: 2h. Maximum absorbed power from the net: 2.600W
 

BATTERY PACK
N° 2 Symmetrical Battery Packs LifePO4.
Estimated battery duration for a medium usage with recovery of energy during the braking phase: about 1h
- Recharge time: about 2h per each run-down battery pack
Battery Pack life- discharged/charged cycles: 5.000 

pdf Download >>

E-XT40-3 E-XT40-2 E-XT40-4 E-XT40-6 E-XT40-5
Standard
Chassis Code 99KIXT_CE
Diameter tubes 40 X 2 mm Cr-Mo
Pitch 1060 & 1080 mm
Total width 1470 mm
Total length 2020 mm
Diameter axle 40 X 1040 mm (std.)
Axle bearings 2 sb210/06
Brake system Self-Adjusting
Rear brake disk 180 X 4 mm Steel (std.)
180 X 8 mm Steel (opt.)
Steering wheel 320 mm (std.)
Seat Plastic seat XL o XXL.
Tillett covered (opt.)
Protections Full bodyworks
Special polymer bumpers
Options
Engine Belt and pulley kit
(Specify n. of teeth)
Display Power, RPM, kers, battery level, reverse
Remote control
Power reduction
Power off
Protections Roll bar and security belt
Floor tray with antislip surface
Wheel Alluminium reinforced wheels set with thermic treatment 180 - 125 mm; Pin 17mm standard or 20 mm opt. Pin
Tyeres Bridgestone / Via Rent
10x3.60-5 / 11x6.00-5
10x4.50-5 / 11x7.10-5
Stickers kit Available in varius colours

 

 

 

 

 

XT40Cover

Indoor XT40 Cover


The latest XT40 is based on an evolution of our state-of-the-art 40mm vehicle which presents an extreme heavy duty rental kart capability, being at the same time a kart breed made to perform, as all PAROLIN RACING KART products.

Tube cutting and welding are performed using laser technology machines and tube bending with CNC fully automatic machines.
Chassis are made of seamless special Cr-Mo steel tubes of 40x2 mm in diameter.
With unscrewing accessible bolts, the axle and the rear brake can be easily removed.
This adds to the vehicle's ease of maintenance and repair. Axle is 40x5x1040 mm in diameter.
The Clutch Protection System avoids the simultaneous use of the gas and brake pedals increasing the clutch's service life.
The use of all round polymer bumpers allows the vehicles to slide one against the other at the event of collision.

The new bodywork is revolutionary in design, unlike any other kart available. This new design provides significantly improved safety for driver and kart components. Roll bar and security belts are important devices and must be installed for safe operations and to protect the driver.

Considerable thought is put into designing a chassis that reduces maintenace cost and time. The new XT40 provides a thrilling driving experience for the beginner and experienced driver alike. It is ideally suited for all entertainment activities, including arrive-and-drive, corporate events and endurance events. pdf Download >>

XT40Cover XT40Cover XT40Cover
Standard
Chassis Code 99KIXT_C
Diameter tubes 40 X 2 mm Cr-Mo
Pitch 1060 & 1080 mm
Total width 1470 mm
Total length 2020 mm
Diameter axle 40 X 1040 mm (std.)
Axle bearings 2 sb210/06
Brake system Self-Adjusting
Rear brake disk 180 X 4 mm Steel (std.)
180 X 8 mm Steel (opt.)
Steering wheel 320 mm (std.)
Seat M or L Fiberglass (std.)
Tillett covered (opt.)
Protections Roll bar and security belts
Bodyworks
All-round special polymer bumpers
Options
Engine Briggs&Stratton
Ex21 Subaru
Ex27 Subaru
Gx200 Honda
Gx270 Honda
Gx390 Honda
Belt and pulley kit
(Specify n. of teeth)
Chain and Sprocket kit
( specify n. of teeth )
Steel chain sprocket from 28 to 33 teeth, 428
Steel engine sprocket from 12 to 15 teeth,
428 Eurostar chain (428 HR )
Gasoline pump kit
Protections Anti-slip surface floor tray
Wheel Wheel set 180 - 125 mm reinforced and heat treated aluminium with 17mm standard or 20 mm opt. Pin
Tires Bridgestone / Via Rent
10x3.60-5 / 11x6.00-5
10x4.50-5 / 11x7.10-5
Weight Weight box kit 5 - 10 -15 kg
Decals kit

pdf AVAILABLE OPTIONS



Indoor XT40

The brand new XT40 is a leading edge, a state of the art vehicle which presents an extreme heavy duty rental kart capability, being at the same time a kart breed made to perform, as all PAROLINRACING KART products.
Tube cutting and welding are performed using laser technology machines and tube bending with CNC fully automatic machines.
Chassis are made of seamless special Cr-Mo steel tubes of 40 x 2 mm in diameter.
With unscrewing accessible bolts, the axle and the rear brake can be removed.


This adds to the vehicle's ease of maintenance and repair. Axle is 40 x 5 x 1040 mm in diameter.
The Clutch Protection System avoids the simultaneous use of the gas and brake pedals increasing the clutch's service life.
The use of all round polymer bumpers, expecially in indoor tracks, allows the vehicles to slide one against the other at the event of collision.


Bodyworks, rear axle guards and protective covers over the rotating parts are essential safety components. Roll bar and security belts are important devices too and must be installed for safe operations and to protect the driver.

xt401 xt402 xt403 xt404
Standard
Chassis Code 99KIXT_P
Diameter tubes 40 X 2 mm Cr-Mo
Pitchlt;/em> 1060 & 1080 mm
Total width 1400 mm
Total length 1970 mm
Diameter axle 40 X 960 mm (std.)
Axle bearings 2 sb210/06
Brake system Self-Adjusting
Rear brake disk 180 X 4 mm Steel (std.)
180 X 8 mm Steel (opt.)
Steering wheel 300 mm (std.)
320 mm (opt.)
Seat M or L Fiberglass (std.)
Tillett covered (opt.)
Protections Rear axle cover Red, Blue, Black
Roll bar and security belts
Bodyworks
Options
Engine Fiberglass engine cover for the following engines:
Briggs&Stratton
Ex21 Subaru
Ex27 Subaru
Gx200 Honda
Gx270 Honda
Gx390 Honda
External exhaust pipe kit complete with silencer (located under the rear axle cover)
Belt and pulley kit
(Specify n. of teeth)
Chain and Sprocket kit
( specify n. of teeth )
Steel chain sprocket
from 28 to 33 teeth, 428
Steel engine sprocket
from 12 to 15 teeth,
428 Eurostar chain (428 HR )
Gasoline pump kit
Protections Anti-slip surface floor tray
All-round special polymer bumpers
Wheel Wheel set 180 - 125 mm reinforced and heat treated aluminium with 17mm standard or 20 mm opt. Pin
Tires Bridgestone / Via Rent
10x3.60-5 / 11x6.00-5
10x4.50-5 / 11x7.10-5
Weight Weight box kit 5 - 10 -15 kg
Decals kit

pdf AVAILABLE OPTIONS



Indoor Master

The brand new INDOOR MASTER is a leading edge, a state of the art vehicle which presents an extreme heavy duty rental kart capability, being at the same time a kart breed made to perform, as all PAROLINRACING KART products.
Tube cutting and welding are performed using laser technology machines and tube bending with CNC fully automatic machines.
Chassis are made of seamless special Cr-Mo steel tubes of 32 x 2 mm in diameter. With unscrewing accessible bolts, the axle and the rear brake can be removed: they add to the vehicle's ease of maintenance and repair. Axle is 40 x 960 mm in diameter.

The Clutch Protection System avoids the simultaneous use of the gas and brake pedals increasing the clutch's service life.
The use of all round polymer bumpers, expecially in indoor tracks, allows the vehicles to slide one against the other at the event of collision.

Bodyworks, rear axle guards and protective covers over the rotating parts are essential safety components. Roll bar and security belts are important devices too and must be installed for safe operations and to protect the driver.

IndM-1 IndM-2 IndM-3 IndM-4
Standard
Chassis Code 99KIM_P
Diameter tubes 32 x 2 mm Cr-Mo
Pitch 1060 & 1080 mm
Total width 1280 mm
Total length 1850 mm
Diameter axle 40 x 960 mm (std.)
Axle bearings 2 sb210/06
Brake system Self-Adjusting
Rear brake disk 180 x 4 mm Steel (std.)
180 x 8 mm Steel (opt.)
Steering wheel 320 mm (std.)
Seat XL or XXL pl. Tillett (std.)
Tillett covered (opt.)
Protections Rear axle cover
Red, Blue, Black
Options
Engine Fiberglass Engine cover for the following engines:
Briggs&Stratton
Ex21 Subaru
Ex27 Subaru
Gx200 Honda
Gx270 Honda
External exhaust pipe kit complete with silencer (located under the rear axle cover) for the above listed engines
Belt and pulley kit
(Specify n. of teeth)
Chain and Sprocket kit
( specify n. of teeth )
Steel chain sprocket
from 28 to 33 teeth, 428
Steel engine sprocket
from 12 to 15 teeth,
428 Eurostar chain (428 HR )
Gasoline pump kit
Protections Roll bar
bodyworks ( standard feature ) Red, Black, Blue
Decals kit
Anti-slip surface floor tray
All-round special polymer bumpers
Wheel Wheel set 180 - 125 mm reinforced and heat treated aluminium with 17mm standard or 20 mm opt. Pin
Tires Bridgestone / Via Rent
10x3.60-5 / 11x6.00-5
10x4.50-5 / 11x7.10-5
Weight Weight box kit 5 - 10 -15 kg

pdf AVAILABLE OPTIONS



Indoor XT32

The brand new XT32 is a leading edge, a state of the art vehicle which presents an extreme heavy duty rental kart capability, being at the same time a kart breed made to perform, as all PAROLINRACING KART products.
Tube cutting and welding are performed using laser technology machines and tube bending with CNC fully automatic machines.
Chassis are made of seamless special Cr-Mo steel tubes of 32x2mm in diameter. With unscrewing accessible bolts, the axle and the rear brake can be removed: they add to the vehicle's ease of maintenance and repair. Axle is 30x960mm or, as an option, 40x5x1000mm in diameter.

The special rear engine position allows the customer to drive with ease and comfort.
The use of all round polymer bumpers, expecially in indoor tracks, allows the vehicles to slide one against the other at the event of collision.

Bodyworks, rear axle guards and protective covers over the rotating parts are essential safety components. Roll bar and security belts are important devices too and must be installed for safe operations and to protect the driver.

XT32-1 XT32-2 XT32-3 XT32-4
Standard
Chassis Code 99KIX32_P
Diameter tubes 32 X 2 mm Cr-Mo
Pitch 1030 mm
Total width 1300 mm
Total length 1800 mm
Diameter axle 30 X 960 mm (std.)
40 x 5 x 1000 mm (opt.)
Brake system Self-Adjusting
Rear brake disk 180 X 4 mm Steel (std.)
180 X 8 mm Steel (opt.)
Steering wheel 300 mm (std.)
320 mm (opt.)
Seat M or L Fiberglass (std.)
Tillett covered (opt.)
Protections Rear axle cover Red, Blue, Black
Roll bar and security belts
Bodyworks
Options
Engine Fiberglass Engine cover
for the following engines
Briggs&Stratton
EX21 Subaru
GX200 Honda
External exhaust pipe kit complete with silencer (located under the rear axle cover)
Belt and pulley kit
(Specify n. of teeth)
Chain and Sprocket kit
( specify n. of teeth )
Steel chain sprocket
from 28 to 33 teeth, 428
Steel engine sprocket
from 12 to 15 teeth,
428 Eurostar chain (428 HR )
Gasoline pump kit
Protections All-round special steel tube bumpers
All-round special polymer bumpers
Wheel
Wheel set 180 - 125 mm reinforced and heat treated aluminium with 17mm standard or 20 mm opt. Pin
Tires Bridgestone / Via Rent
10x3.60-5 / 11x6.00-5
10x4.50-5 / 11x7.10-5
Decals kit

pdf AVAILABLE OPTIONS

Translate

Fim Motors

Eurostar Kart Components

NewJersey

NewJersey

LAST NEWS

Wrooom 2012

  Anche quest'anno la Parolin Racing Kart ha collaborato con successo con il Centro Internazionale Guida Sicura di Andrea de Adamich in occasione dello spettacolare evento Wrooom 2012 a Madonna di Campiglio.

Read more

Formula1 and MotoGp Press Ski Meeting 2012 a Madonna di Campiglio

Formula1 and MotoGp Press Ski Meeting 2012 a Madonna di Campiglio

Parolin Racing Kart è presente a Wrooom 2012, Vi aspettiamo numerosi. Inizio gara venerdi 13 gennaio 2012 ore 16:45:  Potete seguirci anche in TV e in internet su Rai Sport 2:   ore 18:00 Wroom 2012 Mastershow       Programma Wrooom - Formula1 and MotoGp Press Ski Meeting 2012 a Madonna di Campiglio Dall' 8 al 15 Gennaio 2012 le scuderie dei team Ferrari F1 e Ducati MotoGp torneranno a Madonna di Campiglio per il tradizionale evento i...

Read more

Recognition of the FIA by the International Olympic Committee

Recognition of the FIA by the International Olympic Committee

11/01/2012By letter dated 9th December 2011, the President of the International Olympic Committee, Jacques Rogge, has announced that the Fédération Internationale de l’Automobile has been recognised by the IOC.The FIA strongly shares the Olympic sporting values as expressed by the IOC and aimed at developing a better understanding between communities worldwide. With this is mind the FIA affirms its commitments to respect the Olympic Charter, in particular:- to establish a...

Read more

09.01.2012 - The FIA and the CIK celebrate their 2011 Karting Champions

09.01.2012 - The FIA and the CIK celebrate their 2011 Karting Champions

The International Karting Commission of the FIA (CIK-FIA) started the year 2012 in dignified fashion by rewarding its Champion Drivers of the 2011 season on Saturday 7 January in Paris, at the Pavillon Gabriel, near the FIA headquarters and just off the famous Champs Élysées and Place de la Concorde. Opened in the presence of the FIA President, Jean Todt, the ceremony has honou...

Read more

Catalogue

Catalogue

top